1.1.1 Application (without Log In)

Table of Contents   Previous Screen   Next Chapter


This section describes how users can apply without logging in.

The following information is provided in accordance with the procedures.

MEMO: Checking Notes

MEMO: About file downloads

MEMO: Supplementary information when accessing the URL in the notification e-mail.

MEMO: Settings for attached files

MEMO: About the calendar functions


1.      Click [Name of Procedure] from the «List of Procedures Screen».
The «User Login Screen» will be displayed to confirm your login to this service.


Top of Page

2.      Click  To Apply without Registering as a User .
The «Procedures Explanation Screen» will be displayed.


Top of Page

3.      Please confirm the procedure details and read the displayed terms.

Note: A file for download may be attached to the screen.
 Please download the attachment to your PC, since it will be a notification of details about an application or a document that needs to be submitted.
 (For steps, refer to "MEMO: About file downloads".)


Top of Page


<Checking Notes>
If “Notes” appears on the «Procedures Explanation Screen», you must check the box to the left of "I have confirmed.”
You cannot proceed to the next screen without first checking the box.



About file downloads
Note: Differs according to browser.
If a file for download is attached to the «Procedures Explanation Screen» or «Application Details Screen»,
download the file as follows.

1. Click on the attached file.
2. Choose the location where you wish to save the file and select [File Name (N)] and [File Type (T)].
3. Click  Save (S.

4. The download will complete. Click  Close  and continue with procedures from the screen for this service.

Note: If it is a file that needs to be submitted to the service provider, please set up the attachment file in «Application Screen» after entering the necessary information.
 (For details, refer to "MEMO: Settings for attached files".)


Top of Page

4.       If you click  Agree , the screen to enter your e-mail address will be displayed.
To register by sending a blank e-mail, please click  Send a Blank E-mail .
For a blank e-mail, proceed to Step 5.
To enter a contact e-mail address, enter your [E-mail Address] and click  Complete .
Please proceed to Step 6.

Note: If this function is not shown, you cannot use it.


Note: If you are unable to click [Agree], confirm and scroll through the Terms of Use until the end. Once you have reached the end, [Agree] will become clickable.



E-mail address

Note: Please use an e-mail address that allows you to receive messages.

Note: If the e-mail address is one that you have already completed a [User Registration] for, please log in and apply.
(For details, refer to 1.1.2 Application (with Log In.)

E-mail address


Please re-enter the above e-mail address for confirmation.


Use either function to receive the e-mail.

Top of Page

5.      The system will display a new e-mail. Click the  Send  button.
An e-mail containing a URL will be sent to the e-mail address entered earlier, so please proceed to Step 7.

Note: If this function is not shown, you cannot use it.


Top of Page

6.      The «E-mail Delivered Screen» will be displayed and an e-mail with the required URL will be sent to the indicated e-mail address.
 Access the application screen from that URL and continue with the registration process.


Top of Page

7.      Click the URL in the "contact address confirmation e-mail."
  The «Application Screen» will be displayed.


Top of Page

<Supplementary information when accessing the URL in the notification e-mail>

When you click the URL in the received notification e-mail, a new access screen will open and you can enter the rest of the application information on that screen.
You can close the original screen you were using if you no longer require it.

*1: The original access screen
*2: The new access screen
1. If you access the URL in the notification e-mail while keeping the original screen open, a new access screen will open.
2. The original screen will remain open even after accessing the new screen.


Top of Page

8.      Enter the needed information and click  Next .
  The collection (drop-off) location information will be displayed.

Note: Some procedures require you to set up attachment files such as images, etc. in «Application Screen». Please ensure that the information is complete and accurate before setting up the file attachment.
 (For steps, refer to MEMO: Settings for attached files.)

Note: When the message “There is no past collection data with the same address, name (kana), and telephone number” is displayed, please apply by telephone.


● If a map is shown after going to the next screen, you must set your garbage and collection point locations.
 Please see the steps as detailed below.



● Click on the map with “Set garbage location” selected to change your garbage and collection point locations.
● Click on the map with “Set collection point” selected to change only your collection point.


Click to close the descriptions of the icons shown on the map.


This pin indicates the collection point.

This pin indicates the garbage location.


Click on the map and a pop-up will appear to confirm that you want to finalize the changes.
If you are satisfied with the changes, click “Yes”.


You may need to check that there are no errors in where the “collection point” and “garbage location” pins are located.
In that case, if you do not check the box, you will not be able to click the button to proceed to the next screen.


Once you have completed the settings, click "Proceed to confirmation”. You will be taken to the «Application Content Confirmation» screen.

Top of Page


MEMO: Settings for attached files
After entering the required information in the file downloaded from the «Procedures Explanation Screen» or the «Application Details Screen», configure the attached files on the «Application Screen».
Carry out the following operations to set the attached files.
1. Click  Reference...  and the «File Selection Screen» will be displayed.
2. Select the file for attachment from Reference and click  Open (O.
  You will be returned to the «Application Screen».

Note: The following types of file extensions can be sent.
 <gif, jpeg, jpg, png, tif, tiff>

Note: An error message will be displayed if the file type is wrong, the size is too large, or the file is possibly infected with a virus. Click  Delete  and choose the correct file.


Top of Page


<About the calendar function>
This system allows dates to be entered using the calendar function.

● Using the calendar function
1. Click  Select Collection Date  to open the calendar screen.
2. Upcoming dates available for collection are set to appear by default. When necessary, click “<Last Month” or “Next Month>” to move between calendar months.
 The current month and next month can be displayed.
3. Clicking on an applicable date (Gregorian calendar) will enter the date in the Date field.


Note: To cancel the calendar entry, click Close on the bottom right.


Top of Page

9.      Confirm the content and click  Apply .
The   «Application Completion Screen» will be displayed.


Top of Page

10.      An [Application Number] and [Password] will be issued before the application procedure will complete.

Note: The [Application Number] and [Password] are required for authentication when performing an [Application Content Inquiry]. (For details, refer to 2.1.1 Application Inquiry Authentication.)
Note: This information is important, so it is recommended that you keep a copy of it, such as a screen shot.


Top of Page

11.      For completing a procedure that requires entering an e-mail address, the user will receive an e-mail with the [Application Number] and [Password].
   Note: Confirm the content and keep the message in a safe place.


Top of Page